■音源ファイルの準備 Ready to Sound File

サウンドシンクの読み込み可能なファイルフォーマットは、

waveファイル形式のみです。

再生長さに制限はありません。



ファイル名で、各ボタンに割り当てられます。

ファイル名は、次の命名規則に従います。

Reading file format is only file format of wave,

There is not the limit to sound length.



By a file name, it is assigned to each button.

The file name obeys the next naming convention.

ファイル先頭は、バンク名(A-D)、大文字、小文字はどちらでもOK。

. バンク名のあとに続く数字を、スイッチ番号。

. スイッチ番号のあとには、数字を含む任意の文字列もOK。

. ファイルフォーマットを表す拡張子は必ず必要。


例えば、

B001_GLASS.wav

では、バンクBの1に割り当てられます。

The top of the file name is a bank name(A-D)


A capital letter, the small letter are good in both.


.  The number after the bank name is a switch number.

.  The next of the switch number is arbitrary character string including the number.

.  The extension of the file format is necessary.


For example,

B001_GLASS.wav

Then it is assigned to 1 of bank B.

1.PC本体とiPhoneをつなげます。

1. Connect PC and iPhone.

■音源の登録の方法 How to put sound file.

2.iTune 画面のiPhone を選択します。

2.Choose" iPhone" of the iTune screen.

~itunes 11

itunes 12~

3.上部バーの"APP" を選択します。

3.Choose "APP" of the upper part bar.

4.下に「ファイル共有」の「SoundSync」を選択。

右の枠に、音楽ファイル(wave)をドラッグします。


4.Choose "SoundSync" of "File Sharing" below.

On a right frame, Drag a Sound file (wave).

5.次に iPhoneの SoundSync を起動して、

右下の「設定」アイコンをタップ。


5.Next,

Start SoundSync of iPhone and tap a "setting" icon of the lower right.

6.設定画面の上部の「Load Sound File」をタップすると、

ボタンに登録されます。


6.It is registered with a button when you tap upper "Load Sound File" of the setting screen.

■各ボタンの再生設定

One shot = 音の最後で止まるモード

Loop = 繰り返しのループモード


+++


Gate = 押している間だけ再生

Trigger = 1回で最後まで再生


+++


Pause = 再生中に押された場合、そこで一時停止。

Vol = 音の大きさ。 BGMと効果音のバランスなどに。



+++

Sequence = シーケンススイッチ

ファイルネームの順番に再生されます。


Fade In = フェードインで再生を開始し、フェードタイムを15秒まで設定できます。


Fade Out = フェードアウトで再生を止め、フェードタイムを15秒まで設定できます。


Silent Zone = ファイルの頭にブランクの時間を作ります。同様に15秒まで設定できます。


上記設定の組み合わせにより、想像通りに再生できます。

You also have 4 settings of how the sound effect, or music, will be played:


“One shot” = only once.

“Loop” = playing a phrase repeatedly.


+++

“Gate” = plays only while you hold down the button.

Trigger = Continues playing the effect one time even if you release the button.

+++

Pause = Pauses the sound effect or music until you want it to resume playing.

Vol = Volume adjusts the balance of other sound effects and with your

Back Ground Music.

+++

Sequence = sequence switch

And will be played in the order of the file name.


Fade In = starts playing with fade-in, you can set the fade time up to 15 seconds.


To stop the play in Fade Out = fade-out, you can set the fade time up to 15 seconds.


Silent Zone = the head of the file I will make the time of the blank. I can be set similarly up to 15 seconds.


With the combination of the above settings you can have full control

over how all of your sound effects are played!

■音源の削除 How to Delete sound file

iPhoneでは、設定画面の最下にある、"Remove a Sound File"ボタンで削除できますが、iTune上のファイルは削除されません。

In iPhone,can delete it with a "Remove a Sound File" button in the lower of the setting screen, but the file in iTune is not deleted.

iTuneでは、削除したいファイルを選択して、"Del"キーで削除すると、

iPhone上からも削除されます。

n iTune, Choose the file which you want to delete, When you delete it with a "Del" key,

It is deleted by both itune and iPhone.

In iTune, Choose the file which you want to delete, When you delete it with a "Del" key,

It is deleted by both itune and iPhone.

価格 App Storeの価格に準じる

動作環境

◦ iOS8.0以降

• 対応機種

◦ iPhone 4S以降のiPhone

◦ 第5世代以降のiPod touch

■シーケンス音源ファイルの準備 Ready to sequence Sound File

ファイル名で、各ボタンに割り当てられます。

ファイル名は、次の命名規則に従います。

By a file name, it is assigned to each button.

The file name obeys the next naming convention.

ファイル先頭は、バンク名(A-H)、大文字、小文字はどちらでもOK。

.・バンク名のあとに続く数字が、スイッチ番号。


.・ハイフンのあとの番号が、再生される順番の数字。


・その後ろから、任意のファイルネーム。


. ファイルフォーマットを表す拡張子は必ず必要。


例えば、

B001-05_GLASS.wav

では、バンクBの1、シーケンス時、5番目に再生されます。

The top of the file name is a bank name(A-H)

A capital letter, the small letter are good in both.


.  The number after the bank name is a switch number.

.  Number after the hyphen, the numbers of the order to be played.

.  From behind, any file name.


.  The extension of the file format is necessary.


For example,

B001_GLASS.wav

Then it is assigned to 1 of bank B.